Flicker relays:JH series
JH series provides flicker-operation-type relays for AC/DC common use.
The JH Series relays operate at an intermittent cycle of 600 ms. Combining them with the RV Series annunciator relays expands the variation of failure display.
- Reviews (0)
- Features
- Types and Ratings
Be the first to review “Flicker relays:JH series”
Design features
- The electromagnetic relays of an intermittent operation (flicker operation) type for use with both AC and DC allow cyclic flashing of the illuminated bus, illuminated indicators, signal lamps, fault indication lamps, etc. to serve as operation relays that notify supervisors of any control/fault status of the control/protection system. The Series has a wide range of applications including flickering elements of a status indication device or alarm for overinput, overload, speed, position, temperature, pressure, flow rate, etc., and operating elements of general indicator devices for position and direction.
- Compact and lightweight
The compact and lightweight housing measures only 36 x 60 x 68.2 cm and is in the same shape as Fuji’s RV and ADA1P type of annunciator relays. - Fuji’s HH62P-type of power relay with its long life expectancy and high-reliability is used as an output contact, realizing long life expectancy and high reliability.
- 2000 V high dielectric strength High dielectric strength property of 2000 V AC for 1 minute is provided.
- Common input rating (quadruple rating) All of 100 to 110 V AC/DC and 200 to 220 V AC/DC at 50 and 60 Hz inputs are accommodated. (The 24 V and 48 V types have a single rating.)
Specifications/ Flicker relay
Related Products
-
Miniature power relays:HH62,63,64 series
Compact and light weight power relay with 10A contact rating
Product line with 2 poles, 3 poles, and 4 poles under 10A of high capacity contact rating
-
Pushbuttons, Pilot lights:AR22/DR22 series
By adopting the release arm system, ingenious super-effortless mounting is implemented, with consideration of work efficiency.
The AR22 now uses a release arm with a wedge mechanism developed by FujiElectric FA. This enables you to mount or remove the operator and contact block without using any tools. When fitting the switch to a panel, you can ignore the panel thickness. You have only to secure the
operator with a locking nut from behind the panel without any need for adjustment.
-
Pushbuttons, Pilot lights: AR/DR16 minico series
- An integrated structure with built-in contacts that can reduce control panel depth.
- A wide variety of sockets are available to simplify wiring.
- An integrated operator component and contact mechanism that reduces control panel’s depth.
A unified depth of 28.4mm for the Standard type and 35.9mm for the Thin type. - Thin type and Standard type available for your control panel design.
Select an optimum one to match your control panel design.
-
General purpose relays:HH22,23,24 series
Control relay with wide selection of applied models.
These high quality general purpose relays are suitable for multi-pole switching and, although economically priced, are dependable and sturdily constructed.
They are available with coil voltages 24–130V DC and 24–240V AC with continuous current ratings of either 4 or 6 Amps.
Standard contact buttons are silver.
Contact arrangements are 2PDT, 3PDT and SPDT+2NO+1NC.
Relays are enclosed in a polycarbonate dust cover with octal type 8 or 11 pin plugs. -
Card relay:RB series
Compact card relay for print board with low height and narrow width
The RB 104 and 105 relays are designed for printed circuit board use. These relays are extremely thin (5mm) and so, can be densely mounted on PC boards. As a result, PC board size and cost can be greatly reduced. Employing of bifurcated contacts ensure high contact reliability, allowing the RB104, 105 relays to be used in low-level circuits. Coil voltages are available in ranges from 4.5V to 24V DC.
-
Inductive proximity switches Cylindrical type: PE series “PE1-C, PE1-Y and PE2-C”
This proximity switch has a cylindrical shape. The sensor is fitted to an end of the cylinder and the body is provided with a built-in control circuit.
PE1-C, PE1-Y series
DC supply/3-wire and 2-wire system AC supply/2-wire system
Operating distance: 0.8 to 20mm.
This proximity switch has a cylindrical shape.
The sensor is fitted to an end of the cylinder and the body is provided with a built-in control circuit.
This type conforms to the requirements of the CENELEC (Europe) Standards and as the dimensions, ratings and performance comply with the requirements of these Standards, this type can be used as replacement units.PE2-C series
The lineup of PE2-C series proximity switches has been augmented by the addition DC 3-wire system switches withNPN and PNP transistor outputs and 2-wire system switches usable for both AC and DC applications. -
Proximity switches, Magnetically operated reed switches slot type:PM1U series
Slot type switches ideal for conveyer application such as elevators or multi-level parking lifts.
Due to its stable characteristic ensured by the 35mm of slot insertion depth.
This is the optimum choice for locating ferromagnetic-material plate passing through the switch slot. -
Photoelectric switches with built-in amplifier:PH1C series
Photoelectric switches equipped with general-purpose amplifier
Transparent type, retro-reflective type, and diffuse reflection type are available for versatility.
-
Instantaneous stop restart relay:MB4 series
Ideal for use in restarting motor after an instantaneous power failure in large scale industrial units such as plants.
Having the automatic restart in the time of voltage dip as a sequential starting method, this relay helps reducing the workloads of the power supply. 3 types of operating modes such as instantaneous restart, timed restart, and anti-restart are available depending on the duration of the power failure.
-
Photoelectric switches slot-type:PH8AU series
Slot-type photoelectric switches ideal for conveyer application, such as elevators.
Slot-type photoelectric switches ideal for conveyer application, such as elevators and multi-level parking lifts. The emitter and receiver are constructed as a single unit, eliminating the need to adjust the optical axis or sensitivity. Same mounting method as our slot-type magnetically operated reed switches (type PM1U).
Reviews
There are no reviews yet.