Load cells and force transducers

  • AMxWEB

    AM Miniature force transducer

    0 out of 5

    Overview

    The AM force transducers series have been designed to measure static and dynamic compression forces.
    They are particularly suitable for monitoring pounding operations in compression which require a rugged transducer, insensitive to high resonance frequencies caused by non-homogeneous leads in dynamic sequences.
    The accuracy and the stability are not affected by continuous cycling under harsh conditions even with dynamic loads.
    The small size of the AM force transducers makes them ideal for retrofitting in existing equipment.

  • cb

    CB Load cell

    0 out of 5

    Overview

    CB series load cells are designed for trouble free application in industrial environments.
    The cell body and the protective bellows of the strain gauge are in corrosion resistant stainless steel and the bellows are welded using microplasma torch.
    CB load cells are supplied in three grades of accuracy and characteristics.
    The 1000 division is the most economical and suitable for most applications.
    The 2000 division version has a good price/performance ratio.
    The 3000 division is available if higher accuracy is required.
    CB load cells are used in particularly hostile enviroments in the food, petrochemical and pharmaceutical industries and in all applications that demand components in stainless steel and IP67 grade of protection.

  • cc

    CC Cylindrical force transducer

    0 out of 5

    Overview

    The CC force transducers have been designed for use in the plastics industry where it is required to measure the reaction force to the extrusion pressure that is present on the casing of the gearbox along the axis of the extruder screw.
    These models, fitted in contact with the thrust bearings, measure a force whose valve, after suitable correction, is equal to extrusion pressure multiplied by the screw area.
    The CC cylindrical force transducers are all stainless steel construction and configured in such a way that the body, airtight welded, acts also as the case, making a unit that is smaller than the CT series.
    The connector in the shank is on the same axis as the transducer, which in some cases alows easier installation.

  • cir

    CIR Strain gauge transducers

    0 out of 5

    Overview

    The CIR voltage or current amplifiers have been designed to enable the user to adapt non-amplified strain gauge transducers (load cells, pressure transducers) to acquisition systems, PLC, instrumentation with high level inputs.
    The availability of the output in voltage or current enables the signal to be carried over long distances or used in intelligent automation systems

  • cir-d

    CIR-D Galvanically isolated strian gauge transducers

    0 out of 5

    Overview

    The CIR-D voltage or current amplifiers have been designed to enable the user to adapt non-amplified strain gauge transducers (load cells, pressure transducers) to acquisition systems, PLC, instrumentation with high level inputs.
    These amplifiers have galvanic isolation between the supply voltage and the transducer to increase the rejection of noise generated by the power supply itself.
    The availability of the output in current enables the signal to be carried over long distances or used in intelligent automation systems.

  • cm1

    CM Standard size load cell

    0 out of 5

    Overview

    CM series load cells are strain gauge transducers used to measure loads in static and dynamic applications, in compression, with high accuracy.
    They are machined from a single block of metal, so the primary sensing element, the mountings and the case contain no welds allowing smaller dimensions and an enhanced grade of protection. The configuration of the point of measurement, with 8 strain gauges, reduces errors caused by imperfect applications of the load.
    Typical applications of load cells connected in parallel are: silos, hoppers, large weighing platforms.
    The stainless steel construction is suitable for use in aggressive environments in the chemical and petrochemical industries.

  • ct

    CT Toroidal force transducer

    0 out of 5

    Overview

    The CT series force transducers, have been specially designed for use in polymer processing in applications where it is required to measure the reaction force produced by the extru-sion pressure on the gearbox along the axis of the screw.
    They measure a force whose value is indicative of the extrusion pressure over the area of the screw.
    The CT series force transducers can also be used in all other applications where it is required to measure the forces on shafts or columns and in any application where the geometry demands a toroidal form load cell.

  • cu

    CU Small size load cell

    0 out of 5

    Overview

    The CU range of load cells are designed for the measurement of static or dynamic loads in compression.
    All the transducers are calibrated as load cells in units of mass (Kg).
    The CU series is supplied for nominal loads from 50 Kg to 1 T.
    This model has an IP67 protection degree so it can be used in aggressive atmospheres often found in the chemical industries.
    The transducer body is machined from a single piece of stainless steel with no welding.
    This means that it is highly resistant to mechanical shock and vibration.
    The compact size means that these cells can be placed in positions that are difficult to acess and where little space is available.

  • dlc

    DLC Diaphragm load cell without amplifier

    0 out of 5

    Overview

    Pancake like diaphragm load cell designed for the use in Fully electric Injection Molding Machines.
    The Flat-Body design allows for easy integration into the injection unit without adding to the machine length.
    Available with standardized mV/V output or an EEPROMModule to allow for higher mV/V-Output for better signal/noise ratio (to be used with special VDA-Amplfier).
    High-grade steel for endless cycles and optional amplifer necessary.

  • dlca

    DLCA Diaphragm load cell with amplifier

    0 out of 5

    Overview

    Pancake like diaphragm load cell designed for the use in Fully electric Injection Molding Machines.
    The Flat-Body design allows for easy integration into the injection unit without adding to the machine length.

     

  • sb

    SB Low profile load cell

    0 out of 5

    Overview

    The principle of measurement of the SB series of load cells is the deformation caused by the shear generated by the applied load. They are compact load cells with an all stainless steel construction that are extremely rigid towards the measured load and lateral or transverse loads.
    The SB series load cells are the ideal solution for industrial weighing applications such as storage silos, weighing platforms and dosing systems.

  • sh

    SH Standard profile load cell

    0 out of 5

    Overview

    The principle of measurement of the SH series load cells is the deformation caused by the shear generated by the applied load.
    The result is a transducer that is extremely rigid both for the measured load and of lateral or transverse loads which have little effect on it.
    The high degree of accuracy, good level of thermal compensation, the grade of protection make the SH series load cells safe for use in the most severe conditions.